Solder Fume Extractor and Filter Systems

Use the icons on the right to switch between category overview and filtered views.

Soldering fumes must always be extracted

Efficient filtering prevents health risks

A typical electronic solder wire has, along with tin, copper and silver, also flux material, which makes up about 2 to 4 % of the wire weight. Without the flux material it would not be possible to manually solder these wires with soldering irons or hot air flow devices. During the soldering process a portion of the flux material in form from soldering fumes will be released – by lead free soldering is the fume accumulation greater, this is due to the higher temperatures that are necessary to solder lead free wire. The flux material is composed of various resins, acids and activators. At low temperatures it forms the typical resinous rim around the soldering point. At high temperatures the flux material decomposes, forming a cocktail of various materials that is primarily comprised of water vapour and fine dust.

Ventilation or extraction is necessary

In accordance with prevailing regulations, the trade named solder wires sold by Distrelec do not constitute dangerous goods. It is the occupational exposure limits that are important in the assessment of risk associated with manual soldering. Research study has shown that the contamination with respirable fine dust, at a soldering tip temperature of 350 °C and 3,5% flux material and without extraction or ventilation, have a factor of between 1,1 and 17 above the occupational exposure limit. This is completely different when an extraction system is used, then the exposure decreases to a minimum.All solder wire manufacturers and occupational health and safety experts recommend using extraction equipment when soldering. The fine dust contained in soldering fumes can penetrate deep into the lungs and may cause long term damage. Therefore, inhalation of soldering fumes is to be avoided at all times.

90 minutes of soldering with lead-free solder wire — do you want the residue in your lungs?

See video: "Why Solder Fume Extraction?"

  The figure illustrates the correlation between the particle size (left), and the depth of penetration into the lungs (centre). On the right-hand side, the mode of operation for a three-stage soldering fume filter is presented. It is clearly visible for which particle sizes the respective filter stage is designed. See below for the filter structure.

Selection criteria for soldering fume extraction

Point extraction vs area extraction

Point extraction [1] occurs directly at the soldering iron. Disadvantage: Handling of the soldering iron is impeded. Advantage: A lower air volume is required.
Surface extraction [2] occurs by means of a manifold that is placed in a suitable position above the fume source.


Cleaning criteria

Modern, highly efficient extraction equipment use a three-stage filter system consisting of:

  • Class F7/F8 coarse filters
  • Class F13 HEPA filters. Achievable removal level > 99.995%
  • Gas filters with potassium permanganate as the oxidizing agent, and active carbon for the absorption of residual particles

Air volume/flow

On the one hand, an extraction system must be strong enough, but the filter must not "compress" the air:

  • The volume flow and flow velocity at the soldering point must be large enough to extract the fume particles reliably. 0.5 m/s at the soldering tip is required as a minimum
  • In the filter device itself however, the flow velocity must be low so as not to prevent the particles from depositing in the filter. The filters must therefore be large in volume

Easy installation

For the installation of a modern soldering fume extraction system, only a 230-volt power supply is required as the devices operate in recirculation mode. This is possible due to the very high purity of the filtered air, which can therefore subsequently be reintroduced into the ambient air. The extraction system is adapted to the individual soldering workplace using adjustable pipes and suction nozzles. The variability of the suction nozzles is important to ensure that the workplace ergonomics and extraction system operate in unison.


Area extraction Point extraction Accessories

MG140 filter system, dual set

Ready-to-use stand-alone system
for 2 workplaces. 3-stage filters.

Zero Smog 4V

For seamless integration into the Weller
WX family. For up to 4 workplaces.

MG100 filter system, dual set

Compact stand-alone system
for 2 workplaces.


Attractive set including: Extraction
system for 2 workplaces plus
FREE soldering station

Zero Smog 2 Kit 1

Set for 2 workplaces. Easy to install
and operate, with compact dimensions.

HV-2 Set

Great-value fume extractor system for 2
workplaces. Connection-ready with
hoses and filters.

TC Kristall 400

Solder wire with low flux-powder content.

WT 1013 soldering station set

Compact, stackable 95-W soldering station.

Tippy Aktivator

Improves soldering fume absorption
at the soldering tip.